OD |
Date |
Start Time |
End Time |
Duration/seconds |
OBSID/Hex |
SPIRE Script* and/or MOC MOIS Script |
Notes |
|
DD-MM-YYYY |
|
|
|
|
|
187 |
16-11-2009 |
21:30:22 |
22:32:46 |
3744 |
Not set |
H_FCP_SPI_CLOM, H_FCP_OBS_5110, H_FCP_SPI_CLEM and H_COP_SPI_REDB |
Uploading of OBS 4.0.0 into PM and writing it to EEPROM secondary partition |
274 |
11-02-2010 |
20:02:09 |
20:31:32 |
1762 |
0x0000206C |
SpireEngBsmTuneFf/HCSBT2A |
Tuning of BSM Chop Feed Forward Offset and Gain |
302 |
11-03-2010 |
21:02:00 |
21:33:25 |
1884 |
0x0000211D |
SpireEngBsmTuneChopPID/HCSBT3A |
Tuning of BSM Chop PID parameters |
313 |
22-03-2010 |
21:18:44 |
21:49:01 |
1816 |
0x0000211E |
SpireEngBsmTuneChopPID/HCSBT3B |
Tuning of BSM Chop PID parameters |
345 |
23-04-2010 |
20:26:43 |
20:31:47 |
303 |
0x0000211F |
SpireEngPMDump |
PM dump at the standard rate of ~14 PM dump packets per second |
351 |
29-04-2010 |
20:17:31 |
20:31:15 |
823 |
0x00002120 |
SpireEngPatchPM/H_CRP_SPI_APAT |
Patch of PM after two SEUs |
433 |
20-07-2010 |
14:13:04 |
14:27:24 |
859 |
0x00002999 |
SpireEngPatchPM/H_CRP_SPI_APAT |
Patch of PM after SEU |
438 |
25-07-2010 |
14:33:49 |
14:36:21 |
151 |
0x00002121 |
SpireEngSmecLedLvdt/H_COP_SPI_SMLN |
SMEC LED and LVDT sensor switch on before an MTL cooler recycle |
456 |
12-08-2010 |
14:30:07 |
14:49:39 |
1171 |
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU |
467 |
23-08-2010 |
14:01:39 |
14:08:39 |
419 |
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle dump of PM after checksum failure |
468 |
24-08-2010 |
13:58:32 |
14:08:52 |
619 |
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU |
468 |
24-08-2010 |
14:15:04 |
14:34:24 |
1159 |
0x00002122 |
SpireEngPatchTables/H_CRP_SPI_3TAB |
Patch of VM tables after bit-shifts and/or SEUs |
474 |
30-08-2010 |
13:57:03 |
14:23:31 |
1587 |
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle dump of PM after checksum failure |
476 |
01-09-2010 |
14:04:06 |
14:22:14 |
1087 |
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU |
509 |
04-10-2010 |
17:13:15 |
17:24:47 |
691 |
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU in copy of BSW |
514 |
09-10-2010 |
18:36:33 |
18:53:33 |
1019 |
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle PM dump after the SEU which triggered the disabling of the SPIRE sub-schedule. All OD 514 spectrometer observations were lost |
515 |
10-10-2010 |
17:03:04 |
20:51:32 |
13707 |
0x00002999 |
H_CRP_SPI_SEU, Manual Cooler Recycle (H_COP_SPI_MACR), BSM_ON (H_COP_SPI_MBSN), BSM_INIT (H_COP_SPI_MBSI) and PDET_ON (H_COP_SPI_MPHN) |
Manual recovery for OD 515 using updated commissioning procedures |
|
518 |
13-10-2010 |
18:07:09 |
18:20:19 |
789 |
0x00002999 |
SpireEngSmecScan/H_CRP_SPI_SCAN |
To exercise the SMEC stage following failed spectrometer OD 514 |
551 |
15-11-2010 |
16:15 |
16:40 |
|
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU |
579 |
13-12-2010 |
12:05 |
12:15 |
|
0x00002999 |
DPU_START/H_COP_SPI_NSON |
Switch on of the DPU and reboot of OBS 4.0.0 from the secondary partition |
579 |
13-12-2010 |
12:20 |
12:30 |
|
0x00002999 |
SpireEngLoadAllTables/H_CRP_SPI_LTAB |
Load all the VM and OBS tables |
579 |
13-12-2010 |
12:32 |
12:40 |
|
0x00002999 |
DRCU_START/H_COP_SPI_MDRN |
Switch on of the DRCU |
579 |
13-12-2010 |
12:42 |
12:45 |
|
0x00002999 |
SCU_ON/H_COP_SPI_MSCN |
Switch on of SCU DC/AC thermometry |
579 |
13-12-2010 |
12:46 |
12:55 |
|
0x00002999 |
MCU_BOOT/H_COP_SPI_MMCB |
Boot the MCU, set the SMEC FF offset, FF gain, Kp and Ki. Define the SMEC and MCU Eng frame contents. Enter REDY mode. |
579 |
13-12-2010 |
13:00 |
13:05 |
|
0x00000000 |
SPIRE Start Monitoring |
Start the on-board monitoring using a single manual TC - as specified in the PDF procedure at MOC |
580 |
14-12-2010 |
12:15 |
14:45 |
|
0x00002123 |
SpireEngCoolerRecycle/H_CRP_SPI_CREC |
Manual cooler recycle using the CREC VM |
581 |
15-12-2010 |
12:48 |
12:59 |
|
0x00002125 |
SpireEngREDYtoPHOT_STBY/H_CRP_SPI_R2PH |
Manual REDY to PHOT_STBY mode transition to check JFET switch on |
581 |
15-12-2010 |
13:12 |
13:17 |
|
0x00002127 |
SpireEngPHOT_STBYtoREDY/H_CRP_SPI_PH2R |
Manual PHOT_STBY to REDY mode transition |
581 |
15-12-2010 |
13:19 |
13:30 |
|
0x00002129 |
SpireEngREDYtoPHOT_STBY/H_CRP_SPI_R2PH |
Manual REDY to PHOT_STBY mode transition - repeated because RT science had not been enabled in the first test. Even this second test was performed with the bus profile set to PACS prime, rather than SPIRE prime, leading to loss of several photometer science packets. The use of PACS prime bus profile is confirmed by the DPU pool full events observed in OD 581 - see the health monitoring log http://130.246.35.182/icc/logs/OD_0581//SpireOps_HealthMon_DRCUEvents_OD0581_151210_v1.txt . |
581 |
15-12-2010 |
13:44 |
13:49 |
|
0x0000212B |
SpireEngPHOT_STBYtoREDY/H_CRP_SPI_PH2R |
Manual PHOT_STBY to REDY mode transition |
588 |
22-12-2010 |
~11:45 |
~11:46 |
|
Not set |
NA |
Manual TC sent to define an empty OBS table 0x37 of length 0x10. This was done to stop future TC failures for this table during MTL mode transitions. Second manual TC was sent to report the contents of this empty table as further confirmation that the table was correctly defined on-board. Both TCs were successful, i.e. TM(1,7) reports received. These TCs will also be inserted into the MOIS recovery procedure H_CRP_SPI_LTAB for future contingencies. |
714 |
27-04-2011 |
23:38 |
23:46 |
|
0x00002999 |
DPU_START/H_COP_SPI_NSON |
Switch on of the DPU and reboot of OBS 4.0.0 from the secondary partition |
714 |
27-04-2011 |
23:48 |
23:59 |
|
0x00002999 |
SpireEngLoadAllTables/H_CRP_SPI_LTAB |
Load all the VM and OBS tables |
714 |
28-04-2011 |
00:09 |
00:22 |
|
0x00002999 |
DRCU_START/H_COP_SPI_MDRN |
Switch on of the DRCU |
714 |
28-04-2011 |
00:24 |
00:28 |
|
0x00002999 |
SCU_ON/H_COP_SPI_MSCN |
Switch on of SCU DC/AC thermometry. SUBKTEMP was at ~530mK |
714 |
28-04-2011 |
00:30 |
00:37 |
|
0x00002999 |
MCU_BOOT/H_COP_SPI_MMCB |
Boot the MCU, set the SMEC FF offset, FF gain, Kp and Ki. Define the SMEC and MCU Eng frame contents. Enter REDY mode. |
714 |
28-04-2011 |
00:38 |
00:43 |
|
0x00000000 |
SPIRE Start Monitoring |
Start the on-board monitoring using a single manual TC - as specified in the PDF procedure at MOC |
716 |
29-04-2011 |
21:16 |
21:27 |
|
0x0000212D |
SpireEngREDYtoPHOT_STBY/H_CRP_SPI_R2PH |
Manual REDY to PHOT_STBY mode transition to check JFET switch on |
716 |
29-04-2011 |
21:52 |
21:57 |
|
0x0000212F |
SpireEngPHOT_STBYtoREDY/H_CRP_SPI_PH2R |
Manual PHOT_STBY to REDY mode transition |
716 |
29-04-2011 |
21:57 |
22:00 |
|
0x00000000 |
SPIRE Start Monitoring |
Procedure inadvertently executed despite on-board monitoring being already active. Caused a TC failure but otherwise harmless. |
743 |
26-05-2011 |
22:50 |
23:30 |
|
0x00002130 |
H_CRP_SPI_3TAB |
Patch of VM tables for Monitoring (Table 5) and Functions (Table 100), after detection of SEUs in OD 737. |
769 |
21-06-2011 |
17:58 |
18:15 |
|
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle PM dump following the SEU at start of OD 767. |
770 |
22-06-2011 |
18:07 |
18:16 |
|
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU |
915 |
14-11-2011 |
15:40 |
16:30 |
|
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle PM dump following the SEU at start of OD 915. |
916 |
15-11-2011 |
15:32 |
15:46 |
|
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU |
916 |
15-11-2011 |
16:01 |
18:37 |
|
0x00002999 |
SpireEngCoolerRecycle/H_CRP_SPI_CREC |
Manual cooler recycle using the CREC VM |
916 |
15-11-2011 |
18:42 |
18:54 |
|
0x00002131 |
SpireEngREDYtoPHOT_STBY |
Time-tagged REDY to PHOT_STBY mode transition outside DTCP (MTL version of the script but with OBSID set for manual commanding) |
941 |
10-12-2011 |
12:34 |
12:38 |
|
0x5000DCAF |
ENABLE_TM_GENERATION(SPP0N500=1, SPP1N500=3, SPP2N500=0x19, SPP3N500=0x301) |
Manual TC to start Nominal HK report generation. First step in diagnosing SPIRE status after it entered SAFE mode during cooler recycle in DTCP 940. Note that the OBSID and BBID were still set to the cooler recycle values after the transition to SAFE mode. |
941 |
10-12-2011 |
12:42 |
12:50 |
|
0x5000DCAF |
SPIRE PM Checks |
Manual TCs to check SPIRE PM. The second checksum was found to be incorrect. Expected value: 0x5DC1, Actual Value: 0xFD0A |
941 |
10-12-2011 |
12:57 |
13:06 |
|
0x00002999 |
H_FCP_SPI_DUMP |
SPIRE PM Dump (Fast) |
941 |
10-12-2011 |
13:11 |
13:17 |
|
0x00002999 |
Manual Stack to dump OBS tables (extracted from MOC procedure H_CRP_SPI_REJ2P |
Dump of all OBS tables (except Tables 6 & 7) |
941 |
10-12-2011 |
13:18 |
13:20 |
|
N/A |
TC SwOff_SpireHSDPU_N_L11 |
Switch SPIRE DPU off |
941 |
10-12-2011 |
13:32 |
13:44 |
|
0x00002999 |
DPU_START/H_COP_SPI_NSON |
Switch SPIRE DPU on |
941 |
10-12-2011 |
13:45 |
13:57 |
|
0x00002999 |
SpireEngLoadAllTables/H_CRP_SPI_LTAB |
Load all the VM and OBS tables |
941 |
10-12-2011 |
14:00 |
14:04 |
|
0x00002999 |
DRCU_START/H_COP_SPI_MDRN |
Switch on of the DRCU |
941 |
10-12-2011 |
14:06 |
14:11 |
|
0x00002999 |
SCU_ON/H_COP_SPI_MSCN |
Switch on of SCU DC/AC thermometry. SUBKTEMP was at ~626mK, PUMPHTRTEMP ~ 8.5K |
941 |
10-12-2011 |
14:12 |
14:19 |
|
0x00002999 |
MCU_BOOT/H_COP_SPI_MMCB |
Boot the MCU, set the SMEC FF offset, FF gain, Kp and Ki. Define the SMEC and MCU Eng frame contents. Enter REDY mode. |
941 |
10-12-2011 |
14:20 |
14:35 |
|
0x00000000 |
SPIRE Start Monitoring |
Start the on-board monitoring using a single manual TC - as specified in the PDF procedure at MOC. Checked for events and anomalies for ~15 minutes. All OK. |
971 |
09-01-2012 |
13:35 |
13:58 |
|
0x00002999 |
Edited version of H_CRP_SPI_3TAB |
Patch of VM table for Functions (Table 100), after detection of SEU in OD 964. the manual commanding was performed in the middle of an MTL SPIRE cooler recycle, during DTCP, just before the SPIRE-S ODs 971/972. The OBSID was reset to 0x50000000 (null value for operations) by the manual procedure, while the cooler recycle was still in progress. |
981 |
19-01-2012 |
11:15 |
11:38 |
|
0x00002999 |
H_CRP_SPI_PTAB |
Tables patched were Cooler Recycle (Table 0x53/83) and Actions (Table 0x67/103), after detection of SEUs in OD 977. Since the on-board monitoring had to be stopped to patch these tables, the Monitor table (Table 5), for which an SEU was detected in OD 964, was also successfully patched. |
1149 |
05-07-2012 |
15:48 |
16:05 |
|
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle PM dump following the SEU at start of OD 1149. SPIRE sub-schedule disabled. |
1149 |
05-07-2012 |
16:43 |
16:58 |
|
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU. SPIRE sub-schedule re-enabled. |
1191 |
16-08-2012 |
14:55 |
15:13 |
|
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle PM dump following the SEU at start of OD 1191. SPIRE sub-schedule disabled. |
1192 |
17-08-2012 |
15:22 |
15:40 |
|
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU. SPIRE sub-schedule re-enabled. |
1200 |
25-08-2012 |
16:53 |
17:12 |
|
0x00002999 |
SpireEngSlowPMDump/H_CRP_SPI_DUMP |
Trickle PM dump following the SEU at start of OD 1200. SPIRE sub-schedule disabled. |
1200 |
25-08-2012 |
18:16 |
18:32 |
|
0x00002999 |
H_CRP_SPI_SEU |
Patch of PM after SEU. SPIRE sub-schedule re-enabled. |
1200 |
25-08-2012 |
18:57 |
21:30 |
|
0x00002999 |
SpireEngCoolerRecycle/H_CRP_SPI_REJCL |
Time-tagged cooler recycle outside DTCP (MTL version of the script but with OBSID set for manual commanding) |
1200 |
25-08-2012 |
21:37 |
21:48 |
|
0x00002999 |
SpireEngREDYtoPHOT_STBY/H_CRP_SPI_REJ2P |
Time-tagged REDY to PHOT_STBY mode transition outside DTCP (MTL version of the script but with OBSID set for manual commanding) |
1373 |
14-02-2013 |
20:00 |
20:08 |
|
0x00002999 |
DPU_START/H_COP_SPI_NSON |
Switch on of the DPU and reboot of OBS 4.0.0 from the secondary partition |
1373 |
14-02-2013 |
20:11 |
20:29 |
|
0x00002999 |
SpireEngLoadAllTables/H_CRP_SPI_LTAB Version 9 |
Load all the VM and OBS tables |
1373 |
14-02-2013 |
20:33 |
20:36 |
|
0x00002999 |
DRCU_START/H_COP_SPI_MDRN |
Switch on of the DRCU |
1373 |
14-02-2013 |
20:37 |
20:40 |
|
0x00002999 |
SCU_ON/H_COP_SPI_MSCN |
Switch on of SCU DC/AC thermometry. SUBKTEMP was at ~1.6K |
1373 |
14-02-2013 |
20:41 |
20:44 |
|
0x00002999 |
MCU_BOOT/H_COP_SPI_MMCB |
Boot the MCU, set the SMEC FF offset, FF gain, Kp and Ki. Define the SMEC and MCU Eng frame contents. Enter REDY mode. |
1405 |
18-03-2013 |
13:37:00 |
13:38:00 |
|
0x50000000 - not set |
SPIRE Stop Monitoring |
Stopped the on-board monitoring using a single manual TC, in advance of EoHe to prevent the FDIR triggering unnecessarily. This was agreed with the HSC and MOC in the Planning Telecon (AI:Sched#140_20130602_2). |